收藏本站
LTM4606
OPERATION
Power Module Description
The LTM4606 is a standalone non-isolated switching mode
DC/DC power supply. It can deliver up to 6A of DC output
current with some external input and output capacitors.
This module provides precisely regulated output voltage
programmable via one external resistor from 0.6V DC to
5.0V DC over a 4.5V to 28V input voltage range. The typical
application schematic is shown in Figure 20.
The LTM4606 has an integrated constant on-time current
mode regulator, ultralow R DS(ON) FETs with fast switch-
ing speed and integrated Schottky diodes. With current
mode control and internal feedback loop compensation,
the LTM4606 module has sufficient stability margins and
good transient performance under a wide range of operat-
ing conditions and with a wide range of output capacitors,
even all ceramic output capacitors.
Current mode control provides cycle-by-cycle fast current
limiting. Besides, foldback current limiting is provided in
an overcurrent condition while V FB drops. Internal over-
voltage and undervoltage comparators pull the open-drain
PGOOD output low if the output feedback voltage exits a
±10% window around the regulation point. Furthermore,
in an overvoltage condition, internal top FET M1 is turned
off and bottom FET M2 is turned on and held on until the
overvoltage condition clears.
Input filter and noise cancellation circuits reduce the noise
coupling to I/O sides, and ensure the electromagnetic
interference (EMI) to meet EN55022 Class B limits.
Pulling the RUN pin below 1V forces the controller into its
shutdown state, turning off both M1 and M2. At low load
currents, discontinuous mode (DCM) operation can be
enabled to achieve higher efficiency compared to continu-
ous mode (CCM) by setting the FCB pin higher than 0.6V.
When the DRV CC pin is connected to INTV CC an integrated
5V linear regulator powers the internal gate drivers. If a
5V external bias supply is applied on the DRV CC pin, then
an efficiency improvement will occur due to the reduced
power loss in the internal linear regulator. This is especially
true at the higher input voltage range.
The MPGM, MARG0 and MARG1 pins are used to sup-
port voltage margining, where the percentage of margin
is programmed by the MPGM pin, and the MARG0 and
MARG1 selected margining. The PLLIN pin provides fre-
quency synchronization of the device to an external clock.
The TRACK/SS pin is used for power supply tracking and
soft-start programming.
4606fd
10
For more information www.linear.com/LTM4606
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LTM4607IV#PBF IC BUCK/BOOST SYNC ADJ 5A 141LGA
LTM4608AEV#PBF IC BUCK SYNC ADJ 8A 68LGA
LTM4608IV#PBF IC DC/DC UMODULE 8A 68-LGA
LTM4609IV#PBF IC BUCK/BOOST SYNC ADJ 4A 141LGA
LTM4612IV#PBF IC BUCK SYNC ADJ 5A 133LGA
LTM4613MPV#PBF IC UMODULE DC/DC 8A 133-LGA
LTM4614IV#PBF IC UMODULE DC/DC DUAL 4A 144LGA
LTM4615IV#PBF IC SWIT REG BUCK 4A ADJ 144LGA
相关代理商/技术参数
LTM4606MPV-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow EMI 28VIN, 6A DC/DC μModule
LTM4606V 制造商:LIN 功能描述:MODULE 133-LGA LINEAR, 0843
LTM4607 制造商:LINER 制造商全称:Linear Technology 功能描述:High Effi ciency, Synchronous, 4-Switch Buck-Boost Controller
LTM4607EV#PBF 功能描述:IC BUCK/BOOST SYNC ADJ 5A 141LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*
LTM4607EV#PBF 制造商:Linear Technology 功能描述:DC/DC Converter IC
LTM4607EVPBF 制造商:Linear Technology 功能描述:Conv DC-DC Step Up Step Down
LTM4607EV-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:36VIN, 24VOUT High Effi ciency Buck-Boost DC/DC μModule
LTM4607IV#PBF 功能描述:IC BUCK/BOOST SYNC ADJ 5A 141LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:*